Ingo Reichenbach

Von Oktober 2010 bis Mai 2016 Wissenschaftlicher Mitarbeiter am FBK.

 

Veröffentlichungen

 

Bücher/Buchbeiträge

Aurich, J.C.; Reichenbach, I.G.; Bohley, M. (2014): Ultra-small Micro End Mills. In CIRP Encyclopedia of Production Engineering, pp. 1280–1286.

Zeitschriftenbeiträge

M. Bohley, I. Reichenbach, S. Kieren-Ehses, L. Heberger, P. Arrabiyeh, R. Merz, L. Böhme, J. Hering, B. Kirsch, M. Kopnarski, E. Kerscher, G. von Freymann, J.C. Aurich: Coating of Ultra-Small Micro End Mills: Analysis of Performance and Suitability of Eight Different Hard-Coatings. Journal of Manufacturing and Materials Processing 2/2 (2018): S. 22.

Aurich, J.C.; Bohley, M.; Reichenbach, I.G.; Kirsch, B. (2017): Surface quality in micro milling: Influences of spindle and cutting parameters. In CIRP Annals - Manufacturing Technology (66/1), pp. 101–104.

Aurich, J.C.; Reichenbach, I.G.; Schüler, G. M. (2012): Manufacture and application of ultra-small micro end mills. In CIRP Annals - Manufacturing Technology (61/1), pp. 83–86.

Aurich, J.C.; Reichenbach, I.G.; Walk, M.; Carrella, M. (2011): Detektion von Oberflächen in der spanenden Mikrobearbeitung - Bestimmen der Relativposition zwischen Werkzeug und Werkstück in Desktop-Bearbeitungsmaschinen. In wt Werkstattstechnik online (101/6), pp. 413–418.

Bohley, M.; Merz, R.; Müller-Renno, C.; Reichenbach, I.G.; Davoudi, N.; Ziegler, C. et al. (2014): Werkzeug-Werkstück-Interaktion beim Mikrofräsen - Charakterisierung des Wirkpaarverhaltens anhand von Spanbildungs- und Oberflächenuntersuchungen. In wt Werkstattstechnik online (104/9), pp. 586–591.

Bohley, M.; Reichenbach, I.G.; Kieren-Ehses, S.; Heberger, L.; Arrabiyeh, P.A.; Merz, R. et al. (2018): Beschichtung von ultrakleinen Mikro-Schaftfräsern: Analyse der Leistung und Eignung von acht verschiedenen Hartbeschichtungen. In Journal of Manufacturing and Materials Processing (2/2). DOI: 10.3390/jmmp2020022.

Reichenbach, I.G.; Aurich, J.C. (2013): Untersuchung der Oberflächengüte beim Mikrofräsen - Einfluss von Prozessparametern und Einstellwinkel der Nebenschneide bei 48 μm Mikroschaftwerkzeugen. In wt Werkstattstechnik online (103/11-12), pp. 847–852.

Reichenbach, I.G.; Bohley, M.; Sousa, F.J.P.; Aurich, J.C. (2018): Micromachining of PMMA - manufacturing of burr-free structures with single-edge ultra-small micro end mills. In The International Journal of Advanced Manufacturing Technology (96/9-12), pp. 3665–3677.

Reichenbach, I.G.; Bohley, M.; Sousa, F.J.P.; Aurich, J.C. (2019): Tool-life criteria and wear behavior of single-edge ultra-small micro end mills. In Precision Engineering (55), pp. 48–58.

Smaga, M.; Beck, T.; Arrabiyeh, P.A.; Reichenbach, I.G.; Kirsch, B.; Aurich, J.C. (2015): Characterization of micro machined surface from TRIP/TWIP steels. In MATEC Web of Conferences – ESOMAT 2015 – 10th European Symposium on Martensitic Transformations 33, 07004-1 - 07004-5.

Sousa, F.J.P.; Hosse, D. S.; Reichenbach, I.G.; Aurich, J.C.; Seewig, J. (2013): Influence of kinematics and abrasive configuration on the grinding process of glass. In Journal of Materials Processing Technology (213/5), pp. 728–739.

Konferenzbeiträge

Bohley, M.; Reichenbach, I.G.; Müller, C.; Aurich, J.C. (2016a): Development of a desktop machine tool for integrated ultra-small micro end mill production and application. In Proceedings of the 11th International Conference on Micro Manufacturing Paper (13).

Bohley, M.; Reichenbach, I.G.; Müller, C.; Kirsch, B.; Aurich, J.C. (2016b): Compact hydrodynamic spindle module for micromachining applications. In 16th international conference on the European Society for Precision Engineering and Nanotechnology.

Müller, C.; Bohley, M.; Reichenbach, I.G.; Aurich, J.C. (2016): In Situ Topology Measurement of Micro Structured Surfaces with a Confocal Chromatic Sensor on a Desktop Sized Machine Tool. In Advanced Materials Research 1140 - Proceedings of the WGP Congress 2016 - Progress in Production Engineering, pp. 392–399.

Müller, C.; Reichenbach, I.G.; Aurich, J.C. (2014): Design and numerical simulation of an air turbine for a high frequency tool spindle. In 9th International Conference on Micro Manufacturing.

Reichenbach, I.G.; Aurich, J.C. (2013): Direct machining of microstructures in polymethyl methacrylate (PMMA) with single-edge micro end mills with diameter 20 μm. In 13th International Conference of the European Society for Precision Engineering & Nanotechnology 2, pp. 35–38.

Reichenbach, I.G.; Aurich, J.C. (2014): Application of CAD/CAM and micro end mills with 20 to 120 µm diameter for the direct machining of microstructures in PMMA. In Advanced Materials Research 907 - Proceedings of the WGP Congress 2012 - Progress in Production Engineering, pp. 299–306.

Reichenbach, I.G.; Becker, S.; Hasse, H.; Aurich, J.C. (2014a): Machining hydrophobic structures with ultra-small micro end mills. In Proceedings of the 14th international conference of the European Society for Precision Engineering & Nanotechnology 2, pp. 136–139.

Reichenbach, I.G.; Bohley, M. (2013): Micromachining of cp-Titanium on a desktop machine - Study on bottom surface quality in micro end milling. In Advanced Materials Research 769 - Proceedings of the WGP Congress 2013 - Progress in Production Engineering, pp. 53–60.

Reichenbach, I.G.; Bohley, M.; Aurich, J.C. (2015): TiAIN coated ultra-small micro end mills. In 15th international conference of the European Society for Precision Engineering and Nanotechnology, pp. 321–322.

Reichenbach, I.G.; Fallenstein, F.; Aurich, J.C. (2014b): CAE Analysis of Single-Edge Micro End Mills - Methodology and Results. In Proceedings of 9th International Conference on Micro Manufacturing.

Smaga, M.; Beck, T.; Arrabiyeh, P.A.; Reichenbach, I.G.; Kirsch, B.; Aurich, J.C. (2015): Characterization of micro machined surface from TRIP/TWIP steels. In MATEC Web of Conferences – ESOMAT 2015 – 10th European Symposium on Martensitic Transformations 33, 07004-1 - 07004-5.

Sudermann, H.; Reichenbach, I.G.; Aurich, J.C. (2009): Analytical Modeling and Experimental Investigation of Burr Formation in Grinding. In Burrs - Analysis, Control and Removal, pp. 63–71.