• seit September 2017 Wissenschaftlicher Mitarbeiter am FBK
• Forschungsschwerpunkt: Zerspantechnologie

D. Weber, B. Kirsch, E.J. da Silva,  J.C. Aurich: 3D-FEM-Wärmeübertragungssimulation des Schleifens. ZWF - Zeitschrift für wirtschaftlichen Fabrikbetrieb 117/7-8 (2022): S. 484-488.

C.R. Chighizola, C.R. D’Elia, J.E. Jonsson, D. Weber, B. Kirsch, J.C. Aurich, B.S. Linke, M.R. Hill: The Effect of Bulk Residual Stress on Milling-Induced Residual Stress and Distortion. Experimental Mechanics (2022): [DOI:10.1007/s11340-022-00843-9]

D. Weber, B. Kirsch, J.E. Jonsson, C.R. D’Elia, B.S. Linke, M.R. Hill, J.C. Aurich: Simulation based compensation techniques to minimize distortion of thin-walled monolithic aluminum parts due to residual stresses. CIRP Journal of Manufacturing Science and Technology 38 (2022): S. 427-441.

C.R. Chighizola, C.R. D’Elia, D. Weber, B. Kirsch, J.C. Aurich, B.S. Linke, M.R. Hill: Intermethod Comparison and Evaluation of Measured Near Surface Residual Stress in Milled Aluminum. Experimental Mechanics 61 (2021): S. 1309–1322.

D. Weber, B. Kirsch, K. Gutzeit, B.S. Linke, M.R. Hill, J.C. Aurich: Oberflächenmorphologie gefräster Aluminiumwerkstücke. ZWF - Zeitschrift für wirtschaftlichen Fabrikbetrieb 116/7-8 (2021): S. 452-455.

D. Weber, B. Kirsch, C.R. Chighizola, J.E. Jonsson, C.R. D’Elia, B.S. Linke, M.R. Hill, J.C. Aurich: Analysis of machining-induced residual stresses of milled aluminum workpieces, their repeatability, and their resulting distortion. The International Journal of Advanced Manufacturing Technology 115 (2021): S. 1089–1110.

D. Weber, K. Gutzeit, B. Kirsch, C.R. D’Elia, B.S. Linke, M.R. Hill, J.C. Aurich: Analysis of the effect of cryogenic machining on the quality of milled thin-walled monolithic aluminum structural parts. Proceedings of the 22nd Machining Innovations Conference for Aerospace Industry (2022): S. 29-36.

K. Gutzeit, D. Weber, S. Basten, B. Kirsch, J.C. Aurich: Improving the surface morphology by adjusting the cutting parameters during cryogenic milling of Ti-6Al-4V. Proceedings of the 21th Machining Innovations Conference for Aerospace Industry (2021): S. 24-31.

J.E. Jonsson, M.R. Hill, C.R. Chighizola, C.R. D’Elia, B.S. Linke, D. Weber, B. Kirsch, J.C. Aurich: Milling-Induced Residual Stress and Distortion Under Variations of Bulk Residual Stress. Proceedings of the 31st ASM Heat Treating Society Conference (2021): S. 96-99.

D. Weber, B. Kirsch, C.R. Chighizola, C.R. D’Elia, B.S. Linke, M.R. Hill, J.C. Aurich: Investigation on the scale effects of initial bulk and machining induced residual stresses of thin walled milled monolithic aluminum workpieces on part distortions: experiments and finite element prediction model. Procedia CIRP 102 – Proceedings of the 18th CIRP Conference on Modeling of Machining Operations (2021): S. 337-342.

D. Weber, B. Kirsch, C.R. Chighizola, J.E. Jonsson, C.R. D’Elia, B.S. Linke, M.R. Hill, J.C. Aurich: Finite Element Simulation Combination to Predict the Distortion of Thin Walled Milled Aluminum Workpieces as a Result of Machining Induced Residual Stresses. Open Access Series in Informatics (OASIcs) 89 - 2nd International Conference of the DFG International Research Training Group 2057 – Physical Modeling for Virtual Manufacturing (iPMVM 2020)(2021): S. 11:1-11:21.

D. Weber, B. Kirsch, C.R. D’Elia, B.S. Linke, M.R. Hill, J.C. Aurich: Concept to analyze residual stresses in milled thin walled monolithic aluminum components and their effect on part distortion. Production at the leading edge of technology - Proceedings of the 9th Congress of the German Academic Association for Production Technology (2019): S. 287-296.